Right here below you can locate a good deal of sound guidance about A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't exactly rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging project. If the old tub is readily available, the project can move quickly; if you have to open a wall surface to get rid of the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to move out the old bathtub and also embeded in the new one. Make certain you have actually qualified on your own for the work and also fit trying it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to consider employing one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This post will aid you set up a new bathtub in your bathroom if you have actually currently purchased a brand-new bathtub and do not need to change the arrangement of your previous water pipelines.
Your tools and product checklist should consist of the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the limited access that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the staying water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washers are in location in between the tap and the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Making use of both wood boards under its feet, place the bathtub in the needed setting. The wood boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by examining the level and also changing the feet on the tub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest versatile tap port to the suitable supply pipe by making a compression join; then do the same for the other tap.
Activate the water supply and also examine all joints and also brand-new pipework for leakages and also tighten them if needed. Fill up the tub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub should wait until the bathtub has actually been made use of a minimum of once as this will resolve it right into its last setting.
Preparing for the Installment
To start with, the supporting frame provided with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to avoid strain on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, causing complications with moisture and also possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post on How to Install a Bathtub Yourself. Thank you for taking the time to read our blog post. Appreciated our blog? Please share it. Let another person discover it. I take joy in reading our article about Installing A Bathtub.
Course Detail